8200 and 8400 Series Vision System Specifications
| Specifications | 8200 | 8200C | 8400 | 8400C | 8401 | 8401C | 8402 | 8402C |
|---|---|---|---|---|---|---|---|---|
| Minimum Firmware Requirement | In-Sight version 5.2.0 | In-Sight version 5.5.0 | In-Sight version 5.2.0 | In-Sight version 5.5.0 | In-Sight version 5.2.0 | In-Sight version 5.5.0 | In-Sight version 5.2.0 | In-Sight version 5.5.0 |
| Job/Program Memory | 512MB non-volatile flash memory; unlimited storage via remote network device. | |||||||
| Image Processing Memory | 512MB SDRAM | |||||||
| Sensor Type | 1/1.8 inch CMOS, global shutter | |||||||
| Sensor Properties | 3.6mm diagonal, 4.5 x 4.5μm sq. pixels | 7.38mm diagonal, 4.5 x 4.5μm sq. pixels | 9mm diagonal, 4.5 x 4.5µm sq. pixels | |||||
| Maximum Resolution (pixels)1You can configure the number of image sensor rows and set them in the In-Sight Explorer software. If you decrease the number of rows, it increases the frames per second acquired by the vision system. Refer to the AcquireImage topic in the In-Sight® Explorer Help file for more information. | 640 x 480 | 1280 x 1024 | 1600 x 1200 | |||||
| Electronic Shutter Speed | 14µs to 520ms | 17.4µs to 750ms | 20µs to 940ms | |||||
| Acquisition | Rapid reset, progressive scan, full-frame integration. | |||||||
| Bit Depth | 256 grey levels (8 bits/pixel) | 24-bit color | 256 grey levels (8 bits/pixel) | 24-bit color | 256 grey levels (8 bits/pixel) | 24-bit color | 256 grey levels (8 bits/pixel) | 24-bit color |
| Frames Per Second (FPS)2Maximum frames per second are job-dependent, based on the minimum exposure for a full image frame capture using the dedicated acquisition trigger, and assumes there is no user interface connection to the vision system. | 217 FPS | 135 FPS | 217 FPS | 135 FPS | 76 FPS | 45 FPS | 53 FPS | 33 full frames per second. |
| Lens Type | C-Mount | |||||||
| Trigger | 1 opto-isolated, acquisition trigger input. Remote software commands via Ethernet. (RS-232C available when using the optional CIO-MICRO I/O module.) | |||||||
| Discrete Inputs | None. (Eight additional general-purpose inputs available when using the optional CIO-MICRO I/O module.) | |||||||
| Discrete Outputs | 2 opto-isolated, NPN/PNP high-speed output lines. (Eight additional general-purpose outputs available when using the optional CIO-MICRO I/O module.) | |||||||
| Status LEDs | Network, 2 user-configurable. | |||||||
| Network Communication | 1 Ethernet port, 10/100/1000 BaseT with auto MDIX. IEEE 802.3af TCP/IP Protocol. Supports DHCP (factory default), static and link-local IP address configuration. | |||||||
| Serial Communication | None. (RS-232C: 4800 to 115,200 baud rates when connected to the optional CIO-MICRO I/O module.) | |||||||
| Power | Class 2 Power over Ethernet (PoE) device. | |||||||
| Power Type | PoE Type A and Type B. | |||||||
| Power Consumption | 6.49 W maximum per Class 2 PoE. | |||||||
| Current | Per Class 2 PoE requirements. | |||||||
| Voltage | 48VDC nominal, applied from a Class 2 PoE device, which is typically powered from some other voltage. | |||||||
| Material | Die-cast zinc housing. | |||||||
| Finish | Painted. | |||||||
| Mounting | Four M3 threaded mounting holes (1/4-20 and M6 mounting holes also available on accessory mounting block). | |||||||
| Dimensions |
31.0mm (1.22in) x 31.2mm (1.23in) x 75.1mm (2.96in) without accessory mounting block. 39.0mm (1.54in) 31.2mm (1.23in) x 75.1mm (2.96in) with accessory mounting block. |
|||||||
| Weight |
132.2 g (4.66 oz.) without accessory mounting block. 163.2 g (5.76 oz.) with accessory mounting block. |
|||||||
| Case Temperature3Case temperature can be verified using the EV GetSystemConfig(“Internal.Temperature”) Extended Native Mode command. When issued, it returns the vision system's internal temperature in degrees Celsius, which will be ±5 degrees above the vision system case temperature. Refer to the In-Sight® Explorer Help file for more information. Additional cooling measures are required if the case temperature cannot be kept below 50°C. Examples of such measures include: mounting the vision system to a heat sink using the M3 mounting screws, reducing the ambient temperature and ensuring there is air flow over the vision system. | 0°C to 50°C (32°F to 122°F) | |||||||
| Storage Temperature | -20°C to 80°C (-4°F to 176°F) | |||||||
| Humidity | < 80% non-condensing | |||||||
| Protection |
IP40 with cables and lens attached. |
|||||||
| Shock (Shipping and Storage) | IEC 60068-2-27: 18 shocks (3 shocks in each polarity in each (X, Y, Z) axis) 80 Gs (800m/s2 at 11ms, half-sinusoidal) | |||||||
| Vibration (Shipping and Storage) | IEC 60068-2-6: vibration test in each of the three main axis for 2 hours @ 10 Gs (10 to 500 Hz at 100m/s2 / 15mm) | |||||||
| Regulations/Conformity | CE, FCC, KCC, TÜV SÜD NRTL, EU RoHS, China RoHS | |||||||