Default Input and Output Lines

ClosedIn-Sight Micro 1000 Series
Note:
  • HS OUT 0 and HS OUT 1 are built-in high-speed outputs, direct from the vision system.
  • The vision system supports the Strobe signal type for the HSOUT 1 line.

Direct I/O

Output Name
0 HSOUT 0
1 HSOUT 1
4 Green LED
5 Red LED

CIO-MICRO or CIO-MICRO-CC

Input Name
0 Line 0
1 Line 1
2 Line 2
3 Line 3
4 Line 4
5 Line 5
6 Line 6
7 Line 7
Output Name
0 Line 0
1 Line 1
2 Line 2
3 Line 3
4 Line 4
5 Line 5
6 Line 6
7 Line 7
8 HSOUT 0
9 HSOUT 1
10 Green LED
11 Red LED

CIO-WENET

Input Name
0 Line 0
1 Line 1
2 Line 2
3 Line 3
4 Line 4
5 Line 5
6 Line 6
7 Line 7
Output Name
0 Line 0
1 Line 1
2 Line 2
3 Line 3
4 Line 4
5 Line 5
6 Line 6
7 Line 7
8 HSOUT 0
9 HSOUT 1
10 Green LED
11 Red LED
ClosedIn-Sight 2000 Series
Note:
  • IN 0 is a built-in input, direct from the vision sensor.

  • HS OUT 0, HS OUT 1, HS OUT 2 and HS OUT 3 are built-in high-speed outputs, direct from the vision sensor.

  • The vision sensor supports the Strobe signal type for the HSOUT 1 line.
  • Green LED/Red LED is a single LED output, which has both red and green states that you can configure.

Direct I/O

Input Name
0 IN 0
Output Name
0 HSOUT 0
1 HSOUT 1
2 HSOUT 2
3 HSOUT 3
4 Green LED
Red LED
5 Yellow LED

CIO-1400

Input Name
1 Line 1
2 Line 2
3 Line 3
4 Line 4
5 Line 5
6 Line 6
7 Line 7
Output Name
0 HSOUT 0
1 HSOUT 1
2 Line 2
3 Line 3
4 Line 4
Line 5
5 Line 6
7 Line 7
8 Green LED
9 Red LED
10 Yellow LED
11 Disabled
12 Disabled
ClosedIn-Sight 5000 Series

Direct / CIO-1350

Output Name
0 HSOUT 0
1 HSOUT 1
4 Green LED
5 Red LED

CIO-1400

Input Name
1 Line 1
2 Line 2
3 Line 3
4 Line 4
5 Line 5
6 Line 6
7 Line 7
Output Name
0 HSOUT 0
1 HSOUT 1
2 Line 2
3 Line 3
4 Line 4
5 Line 5
6 Line 6
7 Line 7
8 Green LED
9 Red LED

CIO-1450

Note: When Pulsed discrete outputs are sent from a CIO-1450 I/O Module, the pulse width may be 10 milliseconds longer than specified.
Input Name
0 Line 0
1 Line 1
2 Line 2
3 Line 3
4 Line 4
5 Line 5
6 Line 6
7 Line 7
Output Name
0 Line 0
1 Line 1
2 Line 2
3 Line 3
4 Line 4
5 Line 5
6 Line 6
7 Line 7
8 HSOUT 0
9 HSOUT 1
10 Green LED
11 Red LED

CIO-1460

Note: When power is cycled on a CIO-1460 I/O module, discrete outputs may fire for approximately 250 microseconds during initialization.
Input Name
0 Line 0
1 Line 1
2 Line 2
3 Line 3
4 Line 4
5 Line 5
6 Line 6
7 Line 7
Output Name
0 Line 0
1 Line 1
2 Line 2
3 Line 3
4 Line 4
5 Line 5
6 Line 6
7 Line 7
8 HSOUT 0
9 HSOUT 1
10 Green LED
11 Red LED
12 Disabled
13 Disabled

CIO-MICRO/CIO-MICRO-CC

Note:
  • The CIO-MICRO I/O module supports In-Sight 5705, 5705C, 5715 with firmware version 5.3.0 and higher.
  • The CIO-MICRO & CIO-MICRO-CC I/O modules support In-Sight 5100 series and 5400 series vision systems with 128MB non-volatile flash memory or higher. Models can be identified by the Type number (821-xxxx-xx). The Type number is located on the label affixed to the vision system. For a complete list of models and supported firmware versions, see Firmware Versions.
Input Name
0 Line 0
1 Line 1
2 Line 2
3 Line 3
4 Line 4
5 Line 5
6 Line 6
7 Line 7
Output Name
0 Line 0
1 Line 1
2 Line 2
3 Line 3
4 Line 4
5 Line 5
6 Line 6
7 Line 7
8 HSOUT 0
9 HSOUT 1
10 Green LED
11 Red LED
ClosedIn-Sight 70xx - 74xx Series
Note:
  • The In-Sight 70xx - 74xx series vision system supports connecting the Breakout cable and the CIO-MICRO or CIO-MICRO-CC I/O module simultaneously.
  • IN 1 is a built-in input, direct from the vision system. Direct (built-in) inputs are only supported when the vision system is connected to the Breakout cable.
  • HS OUT 0, HS OUT 1, HS OUT 2 and HS OUT 3 are built-in high-speed outputs, direct from the vision system. High-speed outputs on In-Sight 70xx - 74xx series vision systems are only supported when the vision system is connected to the Breakout cable.
  • The vision system supports the Strobe signal type for the HSOUT 0 line.
  • If connecting an external strobe device to the In-Sight 70xx - 74xx series vision system's External Light cable, use the Light Settings dialog to configure the external light settings.
  • There are two options for enabling serial communication for the In-Sight 70xx - 74xx series vision system: using the Breakout cable or using the CIO-MICRO or CIO-MICRO-CC I/O module. When connected to the Breakout cable (and there is no connection to an I/O module), the vision system allows one discrete input line and one discrete output line to be configured as Serial Receive and Serial Transmit, respectively. For more information, see Enable Serial Communication: In-Sight 70xx - 74xx.

Direct I/O

Input Name
1 IN 1/Serial Receive
2 IN 2
3 IN 3
Output Name
0 HS OUT 0
1 HS OUT 1/Serial Transmit
2 HS OUT 2
3 HS OUT 3
4 Green LED
5 Red LED

CIO-MICRO/CIO-MICRO-CC

Note:
  • When the vision system is connected to the Breakout cable and an Ethernet connection to a CIO-MICRO I/O module has been established:
    • The I/O module's I/O port (DB15) and TRIGGER+, TRIGGER-, HS OUT 0, HS OUT 1 and HS COMMON terminals are not supported. Do not connect wire leads from remote devices to these terminals.
    • The I/O module's I/O port (DB15) is not supported. Do not connect anything to this port.
    • The RS-232 TRANSMIT and RS-232 RECEIVE pins on the Breakout cable are disabled. Use the I/O module's RS-232 OUT port (DB9) to connect to a serial device.
Input Name
0 Line 0
1 Line 1
2 Line 2
3 Line 3
4 Line 4
5 Line 5
6 Line 6
7 Line 7
9 IN 1
10 IN 2
11 IN 3
Output Name
0 Line 0
1 Line 1
2 Line 2
3 Line 3
4 Line 4
5 Line 5
6 Line 6
7 Line 7
8 HS OUT 0
9 HS OUT 1
10 HS OUT 2
11 HS OUT 3
12 Green LED
13 Red LED
ClosedIn-Sight 7000 Gen2 Series
Note:
  • The vision system supports connecting the Breakout cable and the CIO-MICRO I/O module simultaneously. For supported hardware I/O configurations, refer to In-Sight 7000 Gen2 Hardware I/O Configurations.
  • IN 1 is a built-in input, direct from the vision system. Direct (built-in) inputs are only supported when the vision system is connected to the Breakout cable.
  • HS OUT 0, HS OUT 1, HS OUT 2 and HS OUT 3 are built-in high-speed outputs, direct from the vision system.
  • The vision system supports the Strobe signal type for the HSOUT 1 line.
  • If connecting an external strobe device to the In-Sight 7000 Gen2 series vision system's External Light cable or if connecting an illumination accessory to the vision system faceplate, use the Light Settings dialog to configure the light settings.

Direct I/O

Note: The vision system supports bi-directional high-speed outputs and general-purpose inputs for IN 2 / HS OUT 2 and IN 3 / HS OUT 3. These lines are configured as outputs by default.
  Input Direction Name
  1 Fixed Input IN 1
  2 Input IN 2
  3 Input IN 3
  Output Direction Name
  0 Fixed Output HSOUT 0
  1 Fixed Output HSOUT 1
  2 Output HSOUT 2
  3 Output HSOUT 3
4 Fixed Output Pass/Fail LED
5 Fixed Output Error LED

CIO-MICRO

Note:
  • When the vision system is connected to the Breakout cable and an Ethernet connection to a CIO-MICRO I/O module has been established:
    • The vision system supports bi-directional high-speed outputs and general-purpose inputs for IN 2 / HS OUT 2 and IN 3 / HS OUT 3. These lines are configured as outputs by default.
    • The CIO-MICRO I/O module's TRIGGER+, TRIGGER-, HS OUT 0, HS OUT 1 and HS COMMON terminals are not supported. Do not connect wire leads from remote devices to these terminals.
    • The RS-232 TRANSMIT and RS-232 RECEIVE pins on the Breakout cable are disabled. Use the I/O module's RS-232 OUT port (DB9) to connect to a serial device.
  • When the vision system is connected to the CIO-MICRO I/O module via the I/O Module cable:
    • The vision system's IN 1, IN 2, IN 3, HS OUT 2 and HS OUT 3 lines are displayed in the Discrete I/O Settings dialog but are not supported. These lines are only supported when the vision system is connected to the Breakout cable.
    • TRIGGER+, TRIGGER-, HS OUT 0, HS OUT 1 and HS COMMON are connected via the CIO-MICRO I/O module terminals.
    • Illumination accessories attached to the vision system faceplate or LIGHT connector are not supported. If these illumination accessories are attached, the Breakout cable must be used to supply power to the vision system and a connection to the I/O module established via Ethernet only.
  Input Direction Name
  0 Fixed Input Line 0
  1 Fixed Input Line 1
  2 Fixed Input Line 2
  3 Fixed Input Line 3
  4 Fixed Input Line 4
  5 Fixed Input Line 5
  6 Fixed Input Line 6
  7 Fixed Input Line 7
  9 Fixed Input IN 1
  10 Input IN 2
  11 Input IN 3
  Output Direction Name
  0 Fixed Output Line 0
  1 Fixed Output Line 1
  2 Fixed Output Line 2
  3 Fixed Output Line 3
  4 Fixed Output Line 4
  5 Fixed Output Line 5
  6 Fixed Output Line 6
  7 Fixed Output Line 7
  8 Fixed Output HSOUT 0
  9 Fixed Output HSOUT 1
  10 Output HSOUT 2
  11 Output HSOUT 3
12 Fixed Output Pass/Fail LED
13 Fixed Output Error LED

CIO-1400

Note:
  • When connected to the CIO-1400 I/O module, the vision system's IN 1, IN 2, IN 3, HS OUT 2 and HS OUT 3 lines are not supported.
  • The CIO-1400 I/O module supports the In-Sight 7000 Gen2 series vision system using In-Sight Explorer 5.4.0 and higher. If you log onto the vision system using an earlier version of In-Sight Explorer, connect to the CIO-1400 I/O module and configure the I/O lines, the changes will not be retained.
  Input Name
  1 Line 1
  2 Line 2
  3 Line 3
  4 Line 4
  5 Line 5
  6 Line 6
  7 Line 7
  Output Name
  0 HSOUT 0
  1 HSOUT 1
  2 Line 2
  3 Line 3
  4 Line 4
  5 Line 5
  6 Line 6
  7 Line 7
8 Pass/Fail LED
9 Error LED
ClosedIn-Sight 8000 Series
Note:
  • HS OUT 0 and HS OUT 1 are built-in high-speed outputs, direct from the vision system.
  • The vision system supports the Strobe signal type for the HSOUT 1 line.
  • If using a strobe with the In-Sight 8405 vision system, a minimum Exposure value of 72ms is recommended for a full frame image capture, to ensure that all pixel rows are exposed when the strobe is pulsed. For more information, see In-Sight 8405 Rolling Shutter Operation.

Direct I/O

Output Name
0 HSOUT 0
1 HSOUT 1 (Strobe is a supported Signal Type)
4 Green LED
5 Red LED

CIO-MICRO

Note: The CIO-MICRO I/O module supports In-Sight 8000 series vision systems with firmware version 5.3.0 and higher.
Input Name
0 Line 0
1 Line 1
2 Line 2
3 Line 3
4 Line 4
5 Line 5
6 Line 6
7 Line 7
Output Name
0 Line 0
1 Line 1
2 Line 2
3 Line 3
4 Line 4
5 Line 5
6 Line 6
7 Line 7
8 HSOUT 0
9 HSOUT 1 (Strobe is a supported Signal Type)
10 Green LED
11 Red LED
ClosedIn-Sight 9902L Line Scan Vision System
Note:
  • The vision system supports connecting the Breakout cable and the CIO-MICRO I/O module simultaneously. For supported hardware I/O configurations, refer to In-Sight 9902L Hardware I/O Configurations.
  • IN 1 is a built-in input, direct from the vision system. Direct (built-in) inputs are only supported when the vision system is connected to the Breakout cable.
  • HS OUT 0 and HS OUT 1 are built-in high-speed outputs, direct from the vision system.
  • The vision system supports the Strobe signal type for the HSOUT 1 line.
  • If using a strobe with the In-Sight 9902L line scan vision system:
    • The strobe should use a PNP wiring configuration and the Strobe/Light Control Trigger should be set to Rising Edge.
    • When the vision system receives an acquisition trigger, the output line sends a pulse and the strobe flashes for the duration of the Exposure time. Once exposure is complete, there must be a minimum of 100µs before the next acquisition trigger is received or the strobe might not function correctly.

Direct I/O

  Input Name
  1 IN 1
  Output Name
  0 HSOUT 0
  1 HSOUT 1
4 Pass/Fail LED
5 Error LED

CIO-MICRO

Note:
  • When the vision system is connected to the Breakout cable and an Ethernet connection to a CIO-MICRO I/O module has been established:
    • The CIO-MICRO I/O module's TRIGGER+, TRIGGER-, HS OUT 0, HS OUT 1 and HS COMMON terminals are not supported. Do not connect wire leads from remote devices to these terminals.
    • The RS-232 TRANSMIT and RS-232 RECEIVE pins on the Breakout cable are disabled. Use the I/O module's RS-232 OUT port (DB9) to connect to a serial device.
  • When the vision system is connected to the CIO-MICRO I/O module via the I/O module cable:
    • The vision system's ENCODER A INPUT and ENCODER B INPUT are not supported.

    • The vision system's IN 1 line is displayed in the Discrete I/O Settings dialog but is not supported. IN 1 is only supported when the vision system is connected to the Breakout cable.

    • TRIGGER+, TRIGGER-, HS OUT 0, HS OUT 1 and HS COMMON are connected via the CIO-MICRO I/O module terminals.
  Input Name
  0 Line 0
  1 Line 1
  2 Line 2
  3 Line 3
  4 Line 4
  5 Line 5
  6 Line 6
  7 Line 7
  9 IN 1
  Output Name
  0 Line 0
  1 Line 1
  2 Line 2
  3 Line 3
  4 Line 4
  5 Line 5
  6 Line 6
  7 Line 7
  8 HSOUT 0
  9 HSOUT 1
10 Pass/Fail LED
11 Error LED

CIO-1400

Note: When connected to the CIO-1400 I/O module, the vision system's ENCODER A INPUT, ENCODER B INPUT and IN 1 lines are not supported.
  Input Name
  1 Line 1
  2 Line 2
  3 Line 3
  4 Line 4
  5 Line 5
  6 Line 6
  7 Line 7
  Output Name
  0 HSOUT 0
  1 HSOUT 1
  2 Line 2
  3 Line 3
  4 Line 4
  5 Line 5
  6 Line 6
  7 Line 7
8 Pass/Fail LED
9 Error LED
ClosedIn-Sight 9912
Note:
  • The vision system supports connecting the Breakout cable and the CIO-MICRO I/O module simultaneously. For supported hardware I/O configurations, refer to In-Sight 9912 Hardware I/O Configurations.
  • IN 1 is a built-in input, direct from the vision system.Direct (built-in) inputs are only supported when the vision system is connected to the Breakout cable.
  • HS OUT 0, HS OUT 1, HS OUT 2 and HS OUT 3 are built-in high-speed outputs, direct from the vision system.
  • The vision system supports the Strobe signal type for the HSOUT 1 line.
  • If connecting an external strobe device to the In-Sight 9912 vision system's External Light cable, use the Light Settings dialog to configure the light settings.

Direct I/O

Note: The vision system supports bi-directional high-speed outputs and general-purpose inputs for IN 2 / HS OUT 2 and IN 3 / HS OUT 3. These lines are configured as outputs by default.
  Input Direction Name
  1 Fixed Input IN 1
  2 Input IN 2
  3 Input IN 3
  Output Direction Name
  0 Fixed Output HSOUT 0
  1 Fixed Output HSOUT 1
  2 Output HSOUT 2
  3 Output HSOUT 3
4 Fixed Output Pass/Fail LED
5 Fixed Output Error LED

CIO-MICRO

Note:
  • When the vision system is connected to the Breakout cable and an Ethernet connection to a CIO-MICRO I/O module has been established:
    • The vision system supports bi-directional high-speed outputs and general-purpose inputs for IN 2 / HS OUT 2 and IN 3 / HS OUT 3. These lines are configured as outputs by default.
    • The CIO-MICRO I/O module's TRIGGER+, TRIGGER-, HS OUT 0, HS OUT 1 and HS COMMON terminals are not supported. Do not connect wire leads from remote devices to these terminals.
    • The RS-232 TRANSMIT and RS-232 RECEIVE pins on the Breakout cable are disabled. Use the I/O module's RS-232 OUT port (DB9) to connect to a serial device.
  • When the vision system is connected to the CIO-MICRO I/O module via the I/O module cable:
    • The vision system's IN 1, IN 2, IN 3, HS OUT 2 and HS OUT 3 lines are displayed in the Discrete I/O Settings dialog but are not supported. These lines are only supported when the vision system is connected to the Breakout cable.
    • TRIGGER+, TRIGGER-, HS OUT 0, HS OUT 1 and HS COMMON are connected via the CIO-MICRO I/O module terminals.
    • Illumination accessories attached to the vision system LIGHT connector are not supported. If these illumination accessories are attached, the Breakout cable must be used to supply power to the vision system and a connection to the I/O module established via Ethernet only.
  Input Direction Name
  0 Fixed Input Line 0
  1 Fixed Input Line 1
  2 Fixed Input Line 2
  3 Fixed Input Line 3
  4 Fixed Input Line 4
  5 Fixed Input Line 5
  6 Fixed Input Line 6
  7 Fixed Input Line 7
  9 Fixed Input IN 1
  10 Input IN 2
  11 Input IN 3
  Output Direction Name
  0 Fixed Output Line 0
  1 Fixed Output Line 1
  2 Fixed Output Line 2
  3 Fixed Output Line 3
  4 Fixed Output Line 4
  5 Fixed Output Line 5
  6 Fixed Output Line 6
  7 Fixed Output Line 7
  8 Fixed Output HSOUT 0
  9 Fixed Output HSOUT 1
  10 Output HSOUT 2
  11 Output HSOUT 3
12 Fixed Output Pass/Fail LED
13 Fixed Output Error LED

CIO-1400

Note: When connected to the CIO-1400 I/O module, the vision system's IN 1, IN 2, IN 3, HS OUT 2 and HS OUT 3 lines are not supported.
  Input Name
  1 Line 1
  2 Line 2
  3 Line 3
  4 Line 4
  5 Line 5
  6 Line 6
  7 Line 7
  Output Name
  0 HSOUT 0
  1 HSOUT 1
  2 Line 2
  3 Line 3
  4 Line 4
  5 Line 5
  6 Line 6
  7 Line 7
8 Pass/Fail LED
9 Error LED

Copyright © 2008 - 2019  |  Cognex Corporation  |  All Rights Reserved.

EasyBuilder Help  |  2019 August 24  |  Revision: 5.7.4.3